MLI3 NEMA 23 Non-captive Linear CANopen IP20

MDrive Linear Actuator

MLI3 NEMA 23 Non-captive Linear CANopen IP20

MDrive CANopen NEMA 23 (57 mm) non-captive linear actuator with expanded I/O set.

Our linear motors feature precision rolled lead screws which are designed specifically for motion control applications to deliver maximum life and quiet operation. Corrosion resistant and non-magnetic, screws are manufactured from premium grade stainless steel. Screws may optionally be ordered with Teflon coating.

Non-captive shaft motor delivers up to 200 lbs (97 kg) of thrust for demanding applications.

Control Type CANopen
Feature Set Expanded (Plus2)
P1 Connector Options Power & I/O Wire Crimp
P2 Connector Options Comm DB9
Communications Interface CANopen
Communications Features CANopen DS301, DSP402
NEMA Size NEMA (mm) 23 (57)
Holding Torque
oz-in (N-cm) 90 (64)
Operating Temperature [°C] heatsink 85
[°C] motor 100
IP rating IP20
California Residents – Click here for Proposition 65 warning
Input Voltage VDC 12 ... 75
Power Supply Current Requirement [A] 2.0/3.5*
Aux-Logic Supply Voltage [+VDC] 12 … 24
Aux-Logic Supply Curret [mA] max 194
Programmable I/O
General Purpose
# of I/O 8 I/O points, programmable as sinking or sourcing inputs or outputs.
Logic Range Inputs and outputs tolerant to +24 VDC, inputs TTL compatible
Output Sink Current Up to 600 mA per channel
Isoation None
Protection Over temp, short circuit, transient over voltage, over voltage, inductive clamp
Dedicated I/O
Function Capture input, trip output , clock/direction I/O
Logic range 0 to +5 VDC, TTL compatible
Analog Input
Resolution [Bits] 10
Range (selectable 0 to +5 VDC, 0 to 10 VDC, 0 to 20 mA, 4 to 20 mA
Type Position and Encoder
Resolution [Bits] 32
Edge Rate [MHz] 5
Range [steps/sec] +/-5,000,000
Resolution [steps/sec] 0.5961
Range [steps/sec2] 1.5 X 109
Resolution [steps/sec2] 90.9
Open Loop
# of step resolutions 20
Range [steps/rev] 200 … 51200
with Encoder option
Encoder type Internal, differential, magnetic
Resolution 512 lines (2048 edges)
Steps/Rev 51200

Force-Speed Performance

Spec Notes Value
Holding torque oz-in 90
N-cm 64
Maximum screw misalignment ° ±1
Maximum thrust lbs 200
kg 97
Maximum repeatability in 0.005
mm 0.127
Rotor inertia oz-in-sec2 0.0025
kg-cm2 0.18
Weight (motor+driver) oz 22.0
g 625.0

Screw G

Screw A

Screw B

Screw D


(1) Test conditions: maximum force/load is based on a static load. This will vary with a dynamic load.

(2) Load limits – 200 lbs (97 kg)

Mechanical dimensions

dimensions in inches (mm)

Screw travel specifications

Travel per revolution
Screw inches mm
Screw G 0.375 9.525
Screw A 0.20 5.08
Screw B 0.167 4.233
Screw D 0.0833 2.116
Travel per full step
Screw inches mm
Screw G 0.001875 0.0476
Screw A 0.001 0.0254
Screw B 0.000835 0.0212
Screw D 0.0004165 0.0106

Dimensional information

Dimensional information
in / mm
A 3.0 to 24.0 / 77.5 to 610.0
in 0.1 / 0.25 increments
B 0.50 / 12.7
C 0.375 / 9.525

Nut specifications

The nut is located internal to the motor.

Max Thrust: 200 lbs (91kg)

End treatment options

End treatments
Smooth Ø 0.2362″ ±0.001
Ø 6mm ±0.003
Threaded  Metric: M6 x 1.0mm
thread to within 0.03″/
0.76 mm of shoulder
UNC: 1/4-20 UNC-2A
thread to within 0.05″/
1.3 mm of shoulder

Need a custom screw solution?

Custom screw ends

SEM offers numerous customization options for your lead screw. Contact us to learn more!

Leadscrew maintenance statement

While under optimal conditions lubrication interval is expected to occur approximately once every 1000 hours of service. Actual life will depend on application and environment. Based upon this, frequent inspections must be performed and a maintenance interval determined based on actual conditions.

Recommended lubricant: Dupont Krytox GPL 206